Island and Table Leg Services
At Osborne Wood Products, all Standard Island and Table Legs will come unfinished and without any cuts or hardware. In order to make your project easier, Osborne offers services specifically for Kitchen Island Legs and Table Legs that can be added to your order.
Please note that all orders with any of the following services added will be considered ‘Custom‘ and are not eligible for return.
You will need to order your products with these services through our Customer Service Department by calling 1-800-849-8876. Services cannot be done online.
Services for Island and Table Legs:
Sanding, Millwork and More:
Sanding to 220 Grit– Our products are sanded to 150 grit as a standard. If you need your items sanded to 220 grit we can do that for you as well. This additional sanding can only be done on Turnings made In House. Please check with our customer service representatives to make sure your items are eligible for this service. There is a $4.00 per item service charge on 220 Grit Sanding.
No Sanding– We can ship an item without any sanding. The item must be manufactured In House and there is no additional charge for this service.
Exterior Glue– Although we do not recommend our products for exterior use you may request exterior glue be used in the production of your products. The items must be manufactured In House. There is a $6.00 per item service charge for using exterior glue.
Quarters– A turning may be sent as quarters (all four quarters sent). The item must be symmetrical in order for the product to be eligible for this service. Note: Quarters does allow for the width of the saw blade and are not “Perfect Quarters.”
Perfect Quarters– We can ship two Perfect Quarters with this service. Again, the product must be symmetrical in order for this service to be applied. Contact customer service for pricing.
¾ Notch Specific Height– Are you adding a turning to a counter or shelf? A height specific ¾ Notch is a custom notching that begins at the top or bottom of the product, and continues for a specified length. The turning must be able to accept millwork to be eligible for this service. Pricing will vary depending on specifications. Contact our customer service representatives for pricing details.
¾ Notch Specific Angle– An angle specific ¾ notch is specified to the desired angle between 45 and 175 degrees (in increments of 5 degrees). Item must be able to accept millwork to be eligible for this service. Pricing will vary depending on turning used. Contact customer service for more pricing details.
Trim Leg– If you have a specific leg style in mind but need it a little shorter we can make this happen without a custom! Trimming is $5.00 per cut per leg. Cuts can be made at the top and/or bottom of the turning.
Chamfer– Our chamfer service is done to the top square of the leg, .5 or 1 inch wide depending on the leg size. You may also specify the length of the chamfer. This service can be done if the top square will accommodate the specified dimensions, and is $2.00 per leg.
Chamfer and Drill Hole– Osborne is also able to Chamfer and drill a hole in the chamfer for your hanger bolt. The width of the chamfer will be .5 or 1 inch depending on leg size. (Length is specified by the customer). The Diameter of the hole may be .125, .25, .375, .5, .625, or .75 inches. The customer may also specify the distance from the top of the leg. Chamfer and drill hole services are $4.00 per leg. (This service will be used if you have your own hardware to install. See Chamfer and Install Bolt/Screw under Installation for pricing of Chamfer with our hardware installed)
Square Hole Through Product– Items manufactured In House may have a square hole through the center of the product. The hole will vary in size (depending largely upon the size of the product and equipment used). This service is $35.00 per leg.
Receptacle Notch– Our receptacle notch service is for the following size: Receptacle notch is cut 5/8” from top, 4” long, 2.5” wide, and 2.25” deep. The item must have a top square in order to be eligible for this service, as the notch will be centered in square. Specifications other than these listed may be done as custom millwork. Contact customer service for availability of other options. The price of our standard receptacle notch is $35.00.
Drill Hole– We are able to drill a hole (less than 3” deep) of several diameters for hardware. Drilled holes can have a diameter of .125, .25, .375, .5, .625, or .75. The hole may be drilled on the top or bottom of the item and will be no deeper than 3”. The service charge is $1.50 per hole drilled.
Shelf Notch– A shelf notch can be added to the bottom of one of our products. The notch will meet your specification of distance from floor and thickness of the notch. Service charge is $35.00 per notch.
Mortise– Legs can be mortised on the top or bottom square of the product. The mortise may apply to 1,2,3 or 4 corners (if 2- opposite or adjacent). Our standard mortise is 3 1/16 long x 5/16 wide x ¾ deep. Items must have a top or bottom square in order to accept the mortise. A $10.00 service charge per leg will apply.
Custom Mortise– If your item requires a mortise that does not match our standard mortise service you may call our customer service to request a price quote for a custom mortise.
Bullnose Edges– Bullnose edges can be added to our products that have a top or bottom square. The item can have this service done to 1,2,3, or 4 corners (if 2- adjacent or opposite) on the top or bottom of the product. Radius of the bullnose edge can be .25, .5, or 1 inch. Service charge is $5.00 per edge.
Custom Milling– Do you have a milling need not mentioned in this section? Contact our friendly customer service representatives for a quote to meet your milling needs. 1-800-849-8876
Install Bolt/Screw– Our Screw Dowels (Part 910HW), or Hanger Bolts (Parts 920HW, 925HW, or 930HW) can all be installed in your product. Hardware will be installed in the top or bottom center of the product. There is an install charge of $1.75 per hardware installed plus the cost of the hardware.
Install Bolt/Screw in Chamfer- Hardware may also be installed in a chamfer. The chamfer will be .5 or 1 inch depending on the size of the leg, with a specified length. Then, the hardware of your choice will be installed at a designated height in the chamfer. Our standard chamfer with bolt installed is .5 (or 1 inch), with a 4 inch length (chamfer). We install part 920HW 2 inches from the top of the leg. This service charge (standard or customer specific) is $5.00 per item.
Custom Install Hardware– Can’t find the installation you need for your product? Request a custom install with our friendly customer service staff at 1-800-849-8876. Prices will vary depending on service.
Rosette Installation– Rosettes can be installed on 1, 2, 3, or 4 sides of a product that has a square (at the top or bottom). Rosettes are installed in the center of the square. The cost is $15.00 per installation plus the cost of the rosettes.
Are you unsure of what you need in order to finish your project? Call our friendly Customer Service Representatives at 1-800-849-8876. They will help you determine what service will be the best option for your design!
Osborne's Mid-Summer Photo Competition!
Table Base Kit Gets the Green Light from Just the Woods!
Live Edge Coffee Table Features Osborne Legs
Custom Quote Process
Exotic Wood Makes a Stunning Desk
How To Assemble the Journeyman Pedestal Base Kit (Part #1186)
Jennifer Shannon Promoted to Osborne Front Office Team Lead
Osborne Presenting in the Big Apple!
Table Construction - Attaching a table leg using a metal corner bracket
Painted Kitchen Island Legs for Contempory Kitchen Style
How to Construct a Mission-Style Coffee Table
How to Install Equalizer Slides for Pedestal Tables
Share Your Project
Dining Table Extends to 16 Feet with Osborne Table Slides
Installing Bun Feet
Osborne Wood Products Sustainability Statement